Product Description
Flush Mount Stainless Steel Corner Guard
36in x 3in x 3in (914.4mm x 76.2mm x 76.2mm)
90 Degree, 14 gauge, Type 304, Satin #4 (Brushed) Finish
For 1/2in drywall, with countersunk mounting holes
This flush mount stainless steel corner guard is made to sit flush with the finished wall surface instead of on top of it, for a clean, built-in look on outside corners. It's sized for 1/2in drywall and formed from 14-gauge Type 304 stainless steel with a #4 satin (brushed) finish, a durable surface that is easy to clean and resists corrosion. At 36in long, it protects the lower part of the corner, where it sits above a wall base or covers one spot that keeps getting hit. The wider 3in wings carry protection farther onto each wall, a good choice where carts or beds strike at an angle.
Features
- Flush mount design for 1/2in drywall
- 14-gauge Type 304 stainless steel, factory-formed with a 1/8in radius corner
- #4 satin (brushed) finish. It ships with a protective film you peel off after installation
- Countersunk mounting holes for a smooth, snag-free face
- 90° profile for standard square outside corners
- Lifetime warranty on the stainless steel against defects in material and workmanship
Specifications
| Length | 36in (914.4mm) |
| Wings | 3in x 3in (76.2mm x 76.2mm) |
| For drywall | 1/2in |
| Angle | 90° |
| Material | Type 304 stainless steel, 14 gauge |
| Finish | #4 satin (brushed) |
| Mounting | Countersunk mounting holes |
| CSI section | 10 26 13 Corner Guards |
Installation & Ordering
It fastens through the countersunk mounting holes; the installation instructions below cover screw and adhesive installation step by step. Peel off the protective covering once it's installed, and clean it with warm water and mild soap, wiping with the grain. Standard lead time is about 6–8 business days. Bulk pricing applies automatically in the cart: 10% off 20–49, 15% off 50+.
Documentation
-
Description
Product Description
Flush Mount Stainless Steel Corner Guard
36in x 3in x 3in (914.4mm x 76.2mm x 76.2mm)
90 Degree, 14 gauge, Type 304, Satin #4 (Brushed) Finish
For 1/2in drywall, with countersunk mounting holesThis flush mount stainless steel corner guard is made to sit flush with the finished wall surface instead of on top of it, for a clean, built-in look on outside corners. It's sized for 1/2in drywall and formed from 14-gauge Type 304 stainless steel with a #4 satin (brushed) finish, a durable surface that is easy to clean and resists corrosion. At 36in long, it protects the lower part of the corner, where it sits above a wall base or covers one spot that keeps getting hit. The wider 3in wings carry protection farther onto each wall, a good choice where carts or beds strike at an angle.
Features
- Flush mount design for 1/2in drywall
- 14-gauge Type 304 stainless steel, factory-formed with a 1/8in radius corner
- #4 satin (brushed) finish. It ships with a protective film you peel off after installation
- Countersunk mounting holes for a smooth, snag-free face
- 90° profile for standard square outside corners
- Lifetime warranty on the stainless steel against defects in material and workmanship
Specifications
Length 36in (914.4mm) Wings 3in x 3in (76.2mm x 76.2mm) For drywall 1/2in Angle 90° Material Type 304 stainless steel, 14 gauge Finish #4 satin (brushed) Mounting Countersunk mounting holes CSI section 10 26 13 Corner Guards Installation & Ordering
It fastens through the countersunk mounting holes; the installation instructions below cover screw and adhesive installation step by step. Peel off the protective covering once it's installed, and clean it with warm water and mild soap, wiping with the grain. Standard lead time is about 6–8 business days. Bulk pricing applies automatically in the cart: 10% off 20–49, 15% off 50+.
Documentation