Product Description
Stainless Steel Bullnose Corner Guard
108in x 4in x 4in(2743.2mm x 101.6mm x 101.6mm)
135 Degree, 18ga, Type 304, Satin #4 (Brushed) Finish
This stainless steel bullnose corner guard protects outside wall corners with a rounded profile instead of a sharp bend, so the corner is softer on hands, hips, carts and equipment that brush past it. It's formed from 18-gauge Type 304 stainless steel with a #4 satin (brushed) finish, a durable surface that is easy to clean and resists corrosion. At 108in long, it covers the corner up to 9 feet, which is floor-to-ceiling in many commercial spaces. The wider 4in wings carry protection farther onto each wall, a good choice where carts or beds strike at an angle.
Features
- 18-gauge Type 304 stainless steel with a rounded bullnose corner
- #4 satin (brushed) finish that hides scuffs and fingerprints
- 135° bullnose profile for angled outside corners. 90° bullnose guards are also available
- Mounting options: Basic (install with your own construction adhesive), Self-Stick Tape, or pre-drilled Holes for #8 stainless screws
- Edge options: Wings (a 10° return bend along each edge) and Rounded Corners, alone or combined
- Lifetime warranty on the stainless steel against defects in material and workmanship (self-stick tape is not covered)
Specifications
| Length | 108in (2743.2mm) |
| Wings | 4in x 4in (101.6mm x 101.6mm) |
| Profile | 135° bullnose (rounded) |
| Material | Type 304 stainless steel, 18 gauge |
| Finish | #4 satin (brushed) |
| Mounting | Basic (customer-supplied adhesive), self-stick tape, or screws |
| CSI section | 10 26 13 Corner Guards |
Installation & Ordering
The Basic option installs with construction adhesive you supply (such as Liquid Nails). You can also order it with Self-Stick Tape or pre-drilled holes for screws. Self-Stick Tape is an installation convenience and is not covered by the warranty. For high-traffic areas or heavy impact, use pre-drilled holes or construction adhesive, alone or together with the tape. Over vinyl wall coverings, trim a strip of the vinyl under each wing so the adhesive bonds to the wall. Peel off the protective covering once it's installed, and clean it with warm water and mild soap, wiping with the grain. Standard lead time is about 6–8 business days. Each bullnose order includes a one-time setup charge ($45 for this length); see below.
Documentation
Why does one bullnose guard cost more?
Every metal bullnose order carries a one-time setup (lot) charge to tool, form and finish the run. It is charged per order, not per piece, so it spreads across everything you order.
For example, at 10 pieces the setup adds $3.50–$4.50 per guard. The more you order, the lower your price per guard.
-
Description
Product Description
Stainless Steel Bullnose Corner Guard
108in x 4in x 4in(2743.2mm x 101.6mm x 101.6mm)
135 Degree, 18ga, Type 304, Satin #4 (Brushed) FinishThis stainless steel bullnose corner guard protects outside wall corners with a rounded profile instead of a sharp bend, so the corner is softer on hands, hips, carts and equipment that brush past it. It's formed from 18-gauge Type 304 stainless steel with a #4 satin (brushed) finish, a durable surface that is easy to clean and resists corrosion. At 108in long, it covers the corner up to 9 feet, which is floor-to-ceiling in many commercial spaces. The wider 4in wings carry protection farther onto each wall, a good choice where carts or beds strike at an angle.
Features
- 18-gauge Type 304 stainless steel with a rounded bullnose corner
- #4 satin (brushed) finish that hides scuffs and fingerprints
- 135° bullnose profile for angled outside corners. 90° bullnose guards are also available
- Mounting options: Basic (install with your own construction adhesive), Self-Stick Tape, or pre-drilled Holes for #8 stainless screws
- Edge options: Wings (a 10° return bend along each edge) and Rounded Corners, alone or combined
- Lifetime warranty on the stainless steel against defects in material and workmanship (self-stick tape is not covered)
Specifications
Length 108in (2743.2mm) Wings 4in x 4in (101.6mm x 101.6mm) Profile 135° bullnose (rounded) Material Type 304 stainless steel, 18 gauge Finish #4 satin (brushed) Mounting Basic (customer-supplied adhesive), self-stick tape, or screws CSI section 10 26 13 Corner Guards Installation & Ordering
The Basic option installs with construction adhesive you supply (such as Liquid Nails). You can also order it with Self-Stick Tape or pre-drilled holes for screws. Self-Stick Tape is an installation convenience and is not covered by the warranty. For high-traffic areas or heavy impact, use pre-drilled holes or construction adhesive, alone or together with the tape. Over vinyl wall coverings, trim a strip of the vinyl under each wing so the adhesive bonds to the wall. Peel off the protective covering once it's installed, and clean it with warm water and mild soap, wiping with the grain. Standard lead time is about 6–8 business days. Each bullnose order includes a one-time setup charge ($45 for this length); see below.
Documentation
Why does one bullnose guard cost more?
Every metal bullnose order carries a one-time setup (lot) charge to tool, form and finish the run. It is charged per order, not per piece, so it spreads across everything you order.
$35 / lotCorner guards under 96"$45 / lotCorner guards over 96"For example, at 10 pieces the setup adds $3.50–$4.50 per guard. The more you order, the lower your price per guard.
