Product Description
Anodized Aluminum Corner Guard
60in x 2in x 2in(1524mm x 50.8mm x 50.8mm)
90 Degree, 060, Type 5005, Satin #4 (Brushed) Finish
This anodized aluminum corner guard protects outside wall corners from carts, dollies, equipment and everyday traffic in hospitals, schools, offices, warehouses and other commercial spaces. It's formed in one piece from .060in-thick Type 5005 pre-anodized aluminum with a #4 satin, clear anodized finish: lightweight, with an anodized surface that resists corrosion and wear. At 60in long, it covers the corner up to 5 feet, which protects it from cart and equipment impacts as well as hands and shoulders. The 2in wings protect the corner edge and the wall right beside it while keeping a slim profile.
Features
- .060in-thick Type 5005 pre-anodized aluminum, factory-formed from a single sheet with a 1/8in radius corner
- #4 satin, clear anodized finish. It ships with a protective film you peel off after installation
- 90° profile for standard square outside corners. 135° and custom angles are also available
- Mounting options: Basic (install with your own construction adhesive), Self-Stick Tape, or pre-drilled Holes for #8 stainless screws
- Edge options: Wings (a 10° return bend along each edge), ArtDeco, and Rounded Corners, alone or combined
- Custom lengths and wing sizes, up to 144in in a single piece
- Lifetime warranty on the aluminum against defects in material and workmanship (self-stick tape is not covered)
Specifications
| Length | 60in (1524mm) |
| Wings | 2in x 2in (50.8mm x 50.8mm) |
| Angle | 90° |
| Material | Type 5005 pre-anodized aluminum, .060in |
| Finish | #4 satin, clear anodized |
| Corner radius | 1/8in (3.2mm) |
| Mounting | Basic (customer-supplied adhesive), self-stick tape, or screws |
| CSI section | 10 26 13 Corner Guards |
Installation & Ordering
The Basic option installs with construction adhesive you supply (such as Liquid Nails), applied in a zig-zag pattern on each inside wing. You can also order it with Self-Stick Tape or pre-drilled holes for screws. Self-Stick Tape is an installation convenience and is not covered by the warranty. For high-traffic areas or heavy impact, use pre-drilled holes or construction adhesive, alone or together with the tape. Over vinyl wall coverings, trim a strip of the vinyl under each wing so the adhesive bonds to the wall. Clean it with warm water and mild soap, then wipe dry. Step-by-step instructions are in the Documentation section below. Standard lead time is about 6–8 business days. If you need guards sooner, see our Ships Today category or call 800-516-4036. Bulk pricing applies automatically in the cart: 10% off 20–49, 15% off 50+.
Documentation
- Drawing 90 Deg - Hole Pattern Approximate (680k)
- Drawing 135 Deg - Hole Pattern Approximate (680k)
- Drawing - 2020 Corner Guard Hole Pattern (102k)
- Suggested Specifications.pdf (250k)
- TheCornerGuardStore Warranty (165k)
- Installation Instructions for Aluminum Corner Guards (495k)
- FAQ - Adhesive Installation
-
Description
Product Description
Anodized Aluminum Corner Guard
60in x 2in x 2in(1524mm x 50.8mm x 50.8mm)
90 Degree, 060, Type 5005, Satin #4 (Brushed) FinishThis anodized aluminum corner guard protects outside wall corners from carts, dollies, equipment and everyday traffic in hospitals, schools, offices, warehouses and other commercial spaces. It's formed in one piece from .060in-thick Type 5005 pre-anodized aluminum with a #4 satin, clear anodized finish: lightweight, with an anodized surface that resists corrosion and wear. At 60in long, it covers the corner up to 5 feet, which protects it from cart and equipment impacts as well as hands and shoulders. The 2in wings protect the corner edge and the wall right beside it while keeping a slim profile.
Features
- .060in-thick Type 5005 pre-anodized aluminum, factory-formed from a single sheet with a 1/8in radius corner
- #4 satin, clear anodized finish. It ships with a protective film you peel off after installation
- 90° profile for standard square outside corners. 135° and custom angles are also available
- Mounting options: Basic (install with your own construction adhesive), Self-Stick Tape, or pre-drilled Holes for #8 stainless screws
- Edge options: Wings (a 10° return bend along each edge), ArtDeco, and Rounded Corners, alone or combined
- Custom lengths and wing sizes, up to 144in in a single piece
- Lifetime warranty on the aluminum against defects in material and workmanship (self-stick tape is not covered)
Specifications
Length 60in (1524mm) Wings 2in x 2in (50.8mm x 50.8mm) Angle 90° Material Type 5005 pre-anodized aluminum, .060in Finish #4 satin, clear anodized Corner radius 1/8in (3.2mm) Mounting Basic (customer-supplied adhesive), self-stick tape, or screws CSI section 10 26 13 Corner Guards Installation & Ordering
The Basic option installs with construction adhesive you supply (such as Liquid Nails), applied in a zig-zag pattern on each inside wing. You can also order it with Self-Stick Tape or pre-drilled holes for screws. Self-Stick Tape is an installation convenience and is not covered by the warranty. For high-traffic areas or heavy impact, use pre-drilled holes or construction adhesive, alone or together with the tape. Over vinyl wall coverings, trim a strip of the vinyl under each wing so the adhesive bonds to the wall. Clean it with warm water and mild soap, then wipe dry. Step-by-step instructions are in the Documentation section below. Standard lead time is about 6–8 business days. If you need guards sooner, see our Ships Today category or call 800-516-4036. Bulk pricing applies automatically in the cart: 10% off 20–49, 15% off 50+.
Documentation
- Drawing 90 Deg - Hole Pattern Approximate (680k)
- Drawing 135 Deg - Hole Pattern Approximate (680k)
- Drawing - 2020 Corner Guard Hole Pattern (102k)
- Suggested Specifications.pdf (250k)
- TheCornerGuardStore Warranty (165k)
- Installation Instructions for Aluminum Corner Guards (495k)
- FAQ - Adhesive Installation
