Product Description
Stainless Steel Cove Base Molding Straight
6in x 120in (152.4mm x 3048mm)
20 gauge, Type 304, Satin #4 (Brushed) Finish
This stainless steel cove base molding protects the bottom of walls from mop buckets, carts, floor machines and foot traffic, where painted walls and vinyl base wear out first. It's made from 20-gauge Type 304 stainless steel with a No. 4 brushed (satin) finish, and its coved bottom edge (3/8in radius) leaves no sharp inside corner at the floor for dirt to collect in. This 6in tall, 120in long straight section runs along the base of the wall; matching pre-formed inside and outside corners finish the corners without field bending.
Features
- 20-gauge Type 304 stainless steel with a coved 3/8in radius bottom edge
- No. 4 brushed (satin) finish (ASTM A480)
- Heights: 4in, 4.75in and 6in
- Lengths: 48in, 94in, 96in and 120in straight sections
- Pre-formed inside and outside corners to match
- Lifetime warranty on the stainless steel against defects in material and workmanship
Specifications
| Type | Straight |
| Height | 6in (152.4mm) |
| Length | 120in (3048mm) |
| Material | Type 304 stainless steel, 20 gauge |
| Finish | No. 4 brushed |
| Installation | Construction adhesive |
| CSI section | 10 26 Wall and Door Protection |
Installation & Ordering
Install it with polyurethane-based construction adhesive after the wall finish is applied, and before finishes such as wall tile, stainless steel wall sheeting or FRP. Clean the wall first so it's free of dirt and loose particles. Step-by-step instructions and CAD drawings are in the Documentation section below. Lead time: Approximately 2-3 weeks until shipment. Questions? Call 800-516-4036.
Documentation
- Complete Documentation Package - all documents in one PDF (2.5 MB)
- Suggested Specifications.pdf
- Brochure and Suggested Specifications.pdf
- TheCornerGuardStore Warranty
- Installation Instructions for Stainless Steel Cove Base Molding
- FAQ - Adhesive Installation
CAD Drawings
-
Description
Product Description
Stainless Steel Cove Base Molding Straight
6in x 120in (152.4mm x 3048mm)
20 gauge, Type 304, Satin #4 (Brushed) FinishThis stainless steel cove base molding protects the bottom of walls from mop buckets, carts, floor machines and foot traffic, where painted walls and vinyl base wear out first. It's made from 20-gauge Type 304 stainless steel with a No. 4 brushed (satin) finish, and its coved bottom edge (3/8in radius) leaves no sharp inside corner at the floor for dirt to collect in. This 6in tall, 120in long straight section runs along the base of the wall; matching pre-formed inside and outside corners finish the corners without field bending.
Features
- 20-gauge Type 304 stainless steel with a coved 3/8in radius bottom edge
- No. 4 brushed (satin) finish (ASTM A480)
- Heights: 4in, 4.75in and 6in
- Lengths: 48in, 94in, 96in and 120in straight sections
- Pre-formed inside and outside corners to match
- Lifetime warranty on the stainless steel against defects in material and workmanship
Specifications
Type Straight Height 6in (152.4mm) Length 120in (3048mm) Material Type 304 stainless steel, 20 gauge Finish No. 4 brushed Installation Construction adhesive CSI section 10 26 Wall and Door Protection Installation & Ordering
Install it with polyurethane-based construction adhesive after the wall finish is applied, and before finishes such as wall tile, stainless steel wall sheeting or FRP. Clean the wall first so it's free of dirt and loose particles. Step-by-step instructions and CAD drawings are in the Documentation section below. Lead time: Approximately 2-3 weeks until shipment. Questions? Call 800-516-4036.
Documentation
- Complete Documentation Package - all documents in one PDF (2.5 MB)
- Suggested Specifications.pdf
- Brochure and Suggested Specifications.pdf
- TheCornerGuardStore Warranty
- Installation Instructions for Stainless Steel Cove Base Molding
- FAQ - Adhesive Installation
CAD Drawings
