Product Description
Stainless Steel Corner Guard
24in x 2.5in x 2.5in(609.6mm x 63.5mm x 63.5mm)
135 Degree, 18 gauge, Type 304, Polished #8 (Mirror) Finish
This stainless steel corner guard protects outside wall corners from carts, dollies, equipment and everyday traffic in hospitals, schools, offices, warehouses and other commercial spaces. It's formed in one piece from 18-gauge Type 304 stainless steel with a #8 mirror (polished) finish: a bright, reflective surface that resists corrosion and wipes clean. At 24in long, it protects the lower part of the corner, where it sits above a wall base or covers one spot that keeps getting hit. The 2.5in wings protect the corner edge and the wall right beside it while keeping a slim profile.
Features
- 18-gauge Type 304 stainless steel, factory-formed from a single sheet with a 1/8in radius corner
- #8 mirror (polished) finish. It ships with a protective film you peel off after installation
- 135° profile for angled outside corners. 90° and custom angles are also available
- Mounting options: Basic (install with your own construction adhesive), Self-Stick Tape, or pre-drilled Holes for #8 stainless screws
- Edge options: Wings (a 10° return bend along each edge), ArtDeco, and Rounded Corners, alone or combined
- Custom lengths and wing sizes, up to 144in in a single piece
- Lifetime warranty on the stainless steel against defects in material and workmanship (self-stick tape is not covered)
Specifications
| Length | 24in (609.6mm) |
| Wings | 2.5in x 2.5in (63.5mm x 63.5mm) |
| Angle | 135° |
| Material | Type 304 stainless steel, 18 gauge |
| Finish | #8 mirror (polished) |
| Corner radius | 1/8in (3.2mm) |
| Mounting | Basic (customer-supplied adhesive), self-stick tape, or screws |
| CSI section | 10 26 13 Corner Guards |
Installation & Ordering
The Basic option installs with construction adhesive you supply (such as Liquid Nails), applied in a zig-zag pattern on each inside wing. You can also order it with Self-Stick Tape or pre-drilled holes for screws. Self-Stick Tape is an installation convenience and is not covered by the warranty. For high-traffic areas or heavy impact, use pre-drilled holes or construction adhesive, alone or together with the tape. Over vinyl wall coverings, trim a strip of the vinyl under each wing so the adhesive bonds to the wall. Clean it with warm water and mild soap, then wipe dry. Step-by-step instructions are in the Documentation section below. Standard lead time is about 6–8 business days. If you need guards sooner, see our Ships Today category or call 800-516-4036.
Documentation
- Drawing 90 Deg - Hole Pattern Approximate (680k)
- Drawing 135 Deg - Hole Pattern Approximate (680k)
- Drawing - 2020 Corner Guard Hole Pattern (102k)
- Suggested Specifications.pdf (250k)
- TheCornerGuardStore Warranty (165k)
- Installation Instructions for Stainless Steel Plate Corner Guards (450k)
- FAQ - Adhesive Installation
-
Description
Product Description
Stainless Steel Corner Guard
24in x 2.5in x 2.5in(609.6mm x 63.5mm x 63.5mm)
135 Degree, 18 gauge, Type 304, Polished #8 (Mirror) FinishThis stainless steel corner guard protects outside wall corners from carts, dollies, equipment and everyday traffic in hospitals, schools, offices, warehouses and other commercial spaces. It's formed in one piece from 18-gauge Type 304 stainless steel with a #8 mirror (polished) finish: a bright, reflective surface that resists corrosion and wipes clean. At 24in long, it protects the lower part of the corner, where it sits above a wall base or covers one spot that keeps getting hit. The 2.5in wings protect the corner edge and the wall right beside it while keeping a slim profile.
Features
- 18-gauge Type 304 stainless steel, factory-formed from a single sheet with a 1/8in radius corner
- #8 mirror (polished) finish. It ships with a protective film you peel off after installation
- 135° profile for angled outside corners. 90° and custom angles are also available
- Mounting options: Basic (install with your own construction adhesive), Self-Stick Tape, or pre-drilled Holes for #8 stainless screws
- Edge options: Wings (a 10° return bend along each edge), ArtDeco, and Rounded Corners, alone or combined
- Custom lengths and wing sizes, up to 144in in a single piece
- Lifetime warranty on the stainless steel against defects in material and workmanship (self-stick tape is not covered)
Specifications
Length 24in (609.6mm) Wings 2.5in x 2.5in (63.5mm x 63.5mm) Angle 135° Material Type 304 stainless steel, 18 gauge Finish #8 mirror (polished) Corner radius 1/8in (3.2mm) Mounting Basic (customer-supplied adhesive), self-stick tape, or screws CSI section 10 26 13 Corner Guards Installation & Ordering
The Basic option installs with construction adhesive you supply (such as Liquid Nails), applied in a zig-zag pattern on each inside wing. You can also order it with Self-Stick Tape or pre-drilled holes for screws. Self-Stick Tape is an installation convenience and is not covered by the warranty. For high-traffic areas or heavy impact, use pre-drilled holes or construction adhesive, alone or together with the tape. Over vinyl wall coverings, trim a strip of the vinyl under each wing so the adhesive bonds to the wall. Clean it with warm water and mild soap, then wipe dry. Step-by-step instructions are in the Documentation section below. Standard lead time is about 6–8 business days. If you need guards sooner, see our Ships Today category or call 800-516-4036.
Documentation
- Drawing 90 Deg - Hole Pattern Approximate (680k)
- Drawing 135 Deg - Hole Pattern Approximate (680k)
- Drawing - 2020 Corner Guard Hole Pattern (102k)
- Suggested Specifications.pdf (250k)
- TheCornerGuardStore Warranty (165k)
- Installation Instructions for Stainless Steel Plate Corner Guards (450k)
- FAQ - Adhesive Installation
